Carbon nanotubes bound for electronics need to be as clean as possible to maximize their utility in next-generation nanoscale devices, and scientists at Rice and Swansea universities have found a way to remove contaminants from the nanotubes.
Rice chemist Andrew Barron, also a professor at Swansea in the United Kingdom, and his team have figured out how to get nanotubes clean and in the process discovered why the electrical properties of nanotubes have historically been so difficult to measure.
Like any normal wire, semiconducting nanotubes are progressively more resistant to current along their length. But over the years, conductivity measurements of nanotubes have been anything but consistent. The Rice-Swansea team wanted to know why.
â€śWe are interested in the creation of nanotube-based conductors, and while people have been able to make wires, their conduction has not met expectations,â€ť Barron said. â€śWe wanted to determine the basic science behind the variability observed by other researchers.â€ť
They discovered that hard-to-remove contaminants â€” leftover iron catalyst, carbon and water â€” could easily skew the results of conductivity tests. Burning those contaminants away, Barron said, creates new possibilities for carbon nanotubes in nanoscale electronics.
The new study appears in the American Chemical Society journalÂ Nano Letters.
The researchers first made multiwalled carbon nanotubes between 40 and 200 nanometers in diameter and up to 30 microns long. They then either heated the nanotubes in a vacuum or bombarded them with argon ions to clean their surfaces.
They tested individual nanotubes the same way one would test any electrical conductor: by touching them with two probes to see how much current passes through the material from one tip to the other. In this case, tungsten probes were attached to a scanning tunneling microscope.
In clean nanotubes, resistance got progressively stronger as the distance increased, as it should. But the results were skewed when the probes encountered surface contaminants, which increased the electric field strength at the tip. And when measurements were taken within 4 microns of each other, regions of depleted conductivity caused by contaminants overlapped, which further scrambled the results.
â€śWe think this is why thereâ€™s such inconsistency in the literature,â€ť Barron said. â€śIf nanotubes are to be the next-generation lightweight conductor, then consistent results, batch-to-batch and sample-to-sample, are needed for devices such as motors and generators as well as power systems.â€ť
Heating the nanotubes in a vacuum above 200 degrees Celsius (392 degrees Fahrenheit) reduced surface contamination, but not enough to eliminate inconsistent results, they found. Argon ion bombardment also cleaned the tubes but led to an increase in defects that degrade conductivity.
Ultimately the researchers discovered vacuumÂ annealingÂ nanotubes at 500 degrees Celsius (932 Fahrenheit) reduced contamination enough to measure resistance accurately.
Barron said engineers who use nanotube fibers or films in devices currently modify the material through doping or other means to get the conductive properties they require. But if the source nanotubes are sufficiently decontaminated, they should be able to get the desired conductivity by simply putting their contacts in the right spot.
â€śA key result of our work is that if contacts on a nanotube are less than 1 micron apart, the electronic properties of the nanotube change from conductor to semiconductor, due to the presence of overlapping depletion zones, which shrink but are still present even in clean nanotubes,â€ť Barron said.
â€śThis has a potential limiting factor on the size of nanotube-based electronic devices,â€ť he said. â€śCarbon-nanotube devices would be limited in how small they could become, soÂ Mooreâ€™s LawÂ would only apply to a point.â€ť
Chris Barnett of Swansea is lead author of the paper. Co-authors are Cathren Gowenlock and Kathryn Welsby, and Rice alumnus Alvin Orbaek White of Swansea. Barron is the Charles W. Duncan Jr.â€“Welch Professor of Chemistry and a professor of materials science and nanoengineering at Rice and the SĂŞr Cymru Chair of Low Carbon Energy and Environment at Swansea.
The Welsh Government SĂŞr Cymru National Research Network in Advanced Engineering and Materials, the SĂŞr Cymru Chair Program, the Office of Naval Research and the Robert A. Welch Foundation supported the research.